1.6.26. Lamps накаливания

Replacement of lamps накаливания demands certain qualification.

On the car some lamps накаливания external illumination can be changed independently. Such lamps concern:

– A passing light lamp (галогенная);

– A headlight lamp;

– All lamps накаливания in back lanterns.

Following lamps накаливания should vary only at the specialised enterprise:

– The xenon light of a head headlight;

– A lamp of the index of turn (a lamp Longlife);

– A lamp of a lay lantern;

– A lamp накаливания an antifog headlight;

– Turn indexes on a wing.

THE NOTE Lamps накаливания are authorised to be changed only for the same. Marks are on a lamp socle.

ATTENTION Lamps накаливания are under pressure and at replacement can burst. Not qualified reference with a high-voltage part of gas-discharge lamps (the xenon light) is life-threatening. Before lamp replacement накаливания switch off light / lay fires.

THE NOTE Regularly check serviceability of all lighting devices of the car and first of all external illumination. Do not concern barehanded a glass flask of a lamp. Use for this purpose a fabric or a paper since the left fingerprint owing to heating of the included lamp накаливания will evaporate, be condensed on a reflecting surface and to worsen reflecting ability of a reflector.

For access to lamps накаливания the right headlight it is necessary to dismantle an air inlet.

Unscrew screws And (fig. 1.179).

Fig. 1.179. An air inlet of the right party of the car

Pull an air inlet from directing In and remove.

After replacement of lamps накаливания the right headlight it is necessary establish an air inlet into place.

Establish an air inlet in assembly position.

In the beginning tighten both screws But only slightly, and then tighten them strongly.

Establish an air inlet in directing to Century

Replacement of lamps by the party of the driver and the forward passenger is carried out in identical sequence.

The mentioned below description of process of replacement of a lamp of a passing light of the basic headlight concerns the party of the driver. Replacement of a lamp of the basic headlight of the party of the forward passenger is carried out (after air inlet dismantle accordingly.

Switch off ignition and light.

Open a cowl.

Fig. 1.180. Removal of a cover of the case (a passing light on the party of the driver) and a cartridge of a lamp of a passing light

On the back end of a cover of the case press downwards unlocking uvula (fig. 1.180) and uncover.

Press a lamp for the plastic tip downwards and take the tip with a lamp from the headlight case.

Separate the plastic tip from a lamp socle.

Lamp installation is facilitated if thus to look through headlight glass.

Fig. 1.181. Lamp installation накаливания and correctly established lamp

Insert a new lamp накаливания into the plastic tip and press against the stop a metal socle of a lamp in the plastic tip (fig. 1.181).

Insert a lamp a ledge upwards into the headlight case.

In the beginning establish a lamp in the lamp case below And.

Track, that the ledge In specified on the centre upwards and entered in directing as is shown in drawing 1.181.

Observe in front through glass of the basic headlight and supervise lamp installation.

Raise the plastic tip in an arrow direction while the lamp will not be fixed in the holder. If it is impossible at once, correct lamp position.

By means of a case cover check up correct position of consolidation.

Establish a case cover below in clamps and press the top party to the basic headlight while above there will be no fixing of a locking uvula.

Check up function new llamas пы накаливания.

As soon as possible check up installation of position of a headlight.

Replacement of lamps by the party of the driver and the forward passenger is carried out in identical sequence.

The mentioned below description of process of replacement of a lamp of a headlight of the basic headlight concerns the party of the driver. Replacement of a lamp of the basic headlight of the party of the forward passenger (after air inlet dismantle it is carried out accordingly.

Switch off ignition and light.

Open a cowl.

Fig. 1.182. Removal of a cover of the case (a headlight on the party of the driver) and a cartridge of a lamp of a headlight

Take away steel bracket case covers in a direction of an arrow and uncover cases (fig. 1.182).

Press the plastic tip of a lamp downwards and take the tip with a lamp from the headlight case.

Separate the plastic tip from a lamp socle.

The directing ledge of a plate of a lamp at installation should enter into a corresponding nest of the case of a lamp.

Fig. 1.183. Lamp installation накаливания (the ledge on a lamp socle at installation should specify upwards)

Insert a new lamp накаливания into the plastic tip and press against the stop a metal socle of a lamp in the plastic tip (fig. 1.183).

Insert a lamp a ledge upwards into the headlight case.

In the beginning establish a lamp in the lamp case below in position And.

Track, that the ledge In specified on the centre upwards and entered in directing as is shown in drawing 1.183.

Raise the plastic tip in an arrow direction while the lamp will not be fixed in the holder. If it is impossible at once, correct lamp position.

By means of a case cover check up correct position of consolidation.

Establish a cover of the case and fix in fixing points steel bracket.

Check up function of a new lamp накаливания.

As soon as possible check up installation of position of a headlight.

For replacement of lamps it is necessary to dismantle a back lantern.

For fastening of a back lantern it is used special конусный (призонный) a bolt. On last turns of process вворачивания the given bolt it is required большее effort.

Define a faulty lamp накаливания.

Open a luggage carrier.

Take from the complete set of the tool a screw-driver.

Use the flat party переставного a screw-driver core.

Before dismantle check up durability of a site of a back lantern (it is necessary for the control after installation).

Fig. 1.184. Position of the fixing screw of a back lantern and dismantle back lateral фопаря

Establish a screw-driver in a groove and separate a cover 1 (fig. 1.184).

Unscrew a screw-driver the screw located under a cover 2 (arrows).

Alternately pull a lantern in a direction of arrows 1 and 2 while the lantern will not be liberated from a support (a position 3 and 4).

Dismantle a lamp arm.

ATTENTION At dismantle of a back lantern care is required to avoid damages of details / of a paint and varnish covering.

THE NOTE Hold near at hand a soft fabric that at laying not to scratch glass of a back lantern.

Dismantle of a lamp arm is necessary for replacement of lamps накаливания.

On an inside of a back lantern two fixing earrings are located.

Deblock fixing earrings And (fig. 1.185).

Fig. 1.185. Fixing earrings from the interior of a back lantern

Remove a lamp arm in a direction of an arrow of Century

Replace a faulty lamp накаливания.

Fig. 1.186. An arrangement of lamps on an arm of the left lateral back lantern: And – a signal of braking and back dimensional fire; In – back dimensional fire; With – a backing headlight; D – the turn index

The lamp arm allows conveniently change all lamps.

Lamps fasten with the help байонетного замкового devices.

Slightly press a lamp into a lamp arm, then turn a lamp to the left and take a faulty lamp.

Establish a new lamp, press it into a cartridge and turn against the stop to the right.

Remove a fabric fingerprints from a glass surface of lamps.

Check up function of lamps накаливания.

Establish into place a lamp arm

The lamp arm is easily mounted.

Check up a correct arrangement of consolidation of a lamp arm.

Establish a lamp arm on a back lantern and level it that it densely adjoined to a lantern.

Press a lamp arm in a back lantern till the fixing moment.

Establish into place a back lantern

The back lantern easily gives in to installation.

Fig. 1.187. Position of the fixing screw of a back lantern and installation of a back lantern

In the beginning bring a back lantern 1 to an arm of a back lantern (fig. 1.187).

Slightly press a back lantern to an arm of a back lantern, observing sequence 2 and 3 while clips strongly will not be fixed in rubber support.

Slightly press the top part of a back lantern and fix its screw from outside a luggage carrier 1. On last turns of process вворачивания the given screw it is required большее effort.

Check up durability of position of a back lantern, подвигав it in the parties.

Establish into place and fix a cover 2 internal facings.

Lay a screw-driver in the tool complete set.

Make sure of serviceability of all back lamps накаливания.

For replacement of lamps накаливания the luggage carrier cover should be opened.

Access to a lamp arm of an internal back lantern opens from the interior of a luggage carrier cover.

Define a faulty lamp.

Take from the complete set of the tool a screw-driver.

Fig. 1.188. Removal of a cover of internal facing of a cover of a luggage carrier and dismantle of a lamp arm

Establish a screw-driver from above in a groove of a cover and смите a cover (fig. 1.188).

Wring out earrings And outside, pull and remove a lamp arm in a direction of an arrow of Century

Replace lamps накаливания.

The lamp arm allows conveniently change all lamps.

Lamps fasten with the help байонетного замкового devices.

Fig. 1.189. An arrangement of lamps накаливания a lamp arm of a back lantern in a luggage carrier cover

Slightly press a lamp into a lamp arm, then turn a lamp to the left and take a faulty lamp.

Establish a new lamp, press it into a cartridge and turn against the stop to the right.

Remove a fabric fingerprints from a glass surface of lamps.

Check up function of lamps накаливания.

Establish into place a lamp arm

Check up a correct arrangement of consolidation of a lamp arm.

Establish a lamp arm on a back lantern and level it that it densely adjoined to a lantern.

Press a lamp arm to a back lantern till the fixing moment.

Establish into place a cover of an internal covering of a cover of a luggage carrier.

Lay a screw-driver in the tool complete set.

Make sure of serviceability of all back lamps накаливания.