Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
1.1. The general data
1.2. Keys, locks of doors
1.3. Controls, a combination of devices and the equipment of salon of the car
1.4. Seats and means of passive safety
1.5. Air-conditioning and heating
1.6. Driving and car service
1.6.1. Engine start-up
1.6.2. A manual brake
1.6.3. The help at a parking ahead and behind
1.6.4. System of regulation of speed
1.6.5. An automatic transmission
1.6.6. A klinotsepnoj variator Multitronic
1.6.7. Operation Multitronic
1.6.8. Electronic system of dynamic stabilisation (ЕSР)
1.6.9. The protivoblokirovochnoe device brake systems
1.6.10. Electronic blocking of differential (ЕDS)
1.6.11. System of regulation of a drive of driving wheels (ASR)
1.6.12. The amplifier of a steering drive
1.6.13. System сервотроник
1.6.14. A full drive (Quattro)
1.6.15. Movement with the trailer
1.6.16. The demountable tjagovo-drawbar
1.6.17. The control of level of oil
1.6.18. A cooling liquid
1.6.19. The storage battery
1.6.20. Стеклоомыватель
1.6.21. Wheel replacement
1.6.22. Поднимание the car
1.6.23. Dismantle / wheel installation
1.6.24. The help of start-up of the engine
1.6.25. Safety locks
1.6.26. Lamps накаливания
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f

1-6-23-demontazh-montazh-kolesa.html

1.6.23. Dismantle / wheel installation

After страгивания wheel bolts and поднимания the car with a jack replace a wheel.

Fig. 1.174. Шестигранник for rotation of bolts and a safety finger


Шестигранником screw-driver handles (from the tool complete set) turn out the most highly located bolt of a wheel and put it on a pure surface (fig. 1.174).
In the released aperture screw in a hand entering into the tool complete set a safety finger.
Then turn out other bolts it agree to the above-stated description.
Remove a wheel. The safety finger remains in an aperture.
Put on a spare wheel through a safety finger.
Screw wheel bolts and with the help шестигранника handles of a screw-driver and slightly tighten them.
Turn out a safety finger and also slightly tighten the given bolt of a wheel.
Wheel bolts should be pure and easily go on a carving. Check up a surface прилегания wheels and naves. Remove pollution on the given surfaces before wheel installation.
Internal шестигранник in the screw-driver handle facilitates вворачивание and a reversing of wheel bolts. The perestavnoj core of a screw-driver should be thus taken out.
At installation of wheels with unidirectional drawing of a protector do not forget about a direction of rotation of a wheel.

THE NOTE
Executed in the screw-driver handle internal шестигранник do not use for страгивания or for an inhaling of wheel bolts.

Tyres with unidirectional drawing of a protector
Tyres with unidirectional drawing of a protector should be mounted taking into account a rotation direction.
The direction of rotation of a wheel is defined by marks in the form of an arrow put on sidewallsе of a tyre cover. Necessarily observe the specified direction of rotation. Only in this case it will be possible to realise optimum qualities of the given tyres, such as absence of propensity to hydroplaning, noiselessness and wear resistance.
Installation of a spare wheel встречно to the direction of movement defined by drawing of a protector, in case of "puncture" demands care at movement as the tyre in this case cannot realise optimum qualities inherent in it to the full. Especially we recommend to remember it in crude weather, соразмеряя speed of movement with a condition проезжей parts.
For full use of advantages of the tyre with unidirectional drawing of a protector as soon as possible replace the damaged tyre for the purpose of restoration of a correct direction of rotation of all tyres.

Locked wheel bolts
For an otvorachivanija/tightening of locked wheel bolts the special adapter is required.
Protective cap 2 remove entering into the tool complete set a plastic clip.
Insert against the stop the adapter 3 into a locked bolt of a wheel 1.

Fig. 1.175. A locked bolt of a wheel with a cap and the adapter



Ballonnyj key establish against the stop on the adapter 3.
Turn on / tighten a wheel bolt.
For cap removal pull a plastic clip over a cap. Thus internal clamps of a clip should be latched in a cap fillet.
It is recommended to carry always in the car the adapter for a locked wheel bolt. Store the adapter together with tools.
At an adapter end face number of a code of blocking of a wheel bolt is beaten out. At enterprise Audi on the basis of given number of a code if necessary it is possible to make the duplicate.


1.6.22. Поднимание the car

1.6.24. The help of start-up of the engine