Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.9. A mechanical part (petrol engines 4,2)
2.9.1. Engine number
2.9.2. Removal and installation semi wedge a belt
2.9.3. Removal and installation damperа крутильных fluctuations
2.9.4. Epiploon replacement crankshaftа on the party of a belt pulley
2.9.5. Removal and installation of a two-mass flywheel
2.9.6. Removal and запрессовка the needle bearing in a flywheel
2.9.7. Removal and installation of a conducted disk
2.9.8. Removal and installation of all covers of chains of a drive
2.9.9. Removal and installation of chains of a drive of camshafts
2.9.10. Removal and installation of a chain drive of the mechanism of management
2.9.11. Removal and installation of a chain of auxiliary drives
2.9.12. An arrangement of loose leaves of the basic bearings on new cranked shaft
2.9.13. An accessory of loose leaves of radical bearings, устанавливаемыхв the block of cylinders
2.9.14. Removal and installation of cam-shafts
2.9.15. Removal and installation of roller levers
2.9.16. Replacement маслосъемных caps
2.9.17. Check of adjustment of phases timing
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







2-9-4-zamena-salnika-kolenvala-na-storone-remennogo-shkiva.html

2.9.4. Epiploon replacement crankshaftа on the party of a belt pulley

Removal
Result a radiator framework in service position.
Remove damper крутильных fluctuations.
Establish an internal part of a stripper манжетного consolidations заподлицо with an external part and fix a bolt with накаткой.

Fig. 2.397. Stripper installation манжетных consolidations


Grease a carving head of a stripper манжетных consolidations by engine oil, establish and, strongly having pressed, twist it as it is possible more deeply in манжетное consolidation (fig. 2.397).
Loosen the a bolt with накаткой and to turn an internal part of a stripper against crankshaftа while the epiploon will not be extended.
Clamp a stripper flat places in a vice.
Remove an epiploon pincers.

Installation
Clear a working and adjoining surface.

Fig. 2.398. Installation манжетного consolidations on a plug


Place the auxiliary adjusting device on насаживаемую the plug and pull манжетное consolidation 1 on насаживаемую the plug (fig. 2.398).
Remove auxiliary the mandrel.

Fig. 2.399. Installation манжетного consolidations on привалочную a surface on the engine


Spread насаживаемую the plug on a cranked shaft and pull манжетное consolidation 1 on привалочную a surface on the engine (fig. 2.399).

THE NOTE
The adjusting plug leave on crankshaftе for запрессовки.

Establish распорную the plug with bolts M8x55 mm on a cranked shaft.
Screw at first bolts effort of a hand.

Fig. 2.400. Запрессовка манжетного consolidations


Tighten bolts alternately on 1/2 turns that запрессовать a sealing ring to the emphasis (fig. 2.400).
The further installation is carried out in return sequence, thus it is necessary observe the following:
– Establish damper крутильных fluctuations.
– Establish a framework of a radiator by means of Ustanovkanyh of details.
– Lower an emphasis against проворачивания at the expense of a body weight on the rubber buffer and fasten bolts.
– Establish a casing of a forward bumper.
– Check up adjustment of headlights.

The inhaling moment
Emphasis of a support of jet bent for to a radiator framework: 28 Нм.


2.9.3. Removal and installation damperа крутильных fluctuations

2.9.5. Removal and installation of a two-mass flywheel