Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.9. A mechanical part (petrol engines 4,2)
2.9.1. Engine number
2.9.2. Removal and installation semi wedge a belt
2.9.3. Removal and installation damperа крутильных fluctuations
2.9.4. Epiploon replacement crankshaftа on the party of a belt pulley
2.9.5. Removal and installation of a two-mass flywheel
2.9.6. Removal and запрессовка the needle bearing in a flywheel
2.9.7. Removal and installation of a conducted disk
2.9.8. Removal and installation of all covers of chains of a drive
2.9.9. Removal and installation of chains of a drive of camshafts
2.9.10. Removal and installation of a chain drive of the mechanism of management
2.9.11. Removal and installation of a chain of auxiliary drives
2.9.12. An arrangement of loose leaves of the basic bearings on new cranked shaft
2.9.13. An accessory of loose leaves of radical bearings, устанавливаемыхв the block of cylinders
2.9.14. Removal and installation of cam-shafts
2.9.15. Removal and installation of roller levers
2.9.16. Replacement маслосъемных caps
2.9.17. Check of adjustment of phases timing
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f


2-9-3-snyatie-i-ustanovka-dempfera-krutilnykh-kolebanijj.html

2.9.3. Removal and installation damperа крутильных fluctuations

Remove
Result a radiator framework in service position.

THE NOTE
For отворачивания and inhalings damperа fluctuations to hold накидным with a key a belt for the central nut of a belt pulley of the generator.


Fig. 2.396. Fixing bolts гасителя крутильных fluctuations


On some turns loosen the 8 fixing bolts гасителя крутильных fluctuations (fig. 2.396).

THE NOTE
Before removal semi wedge a belt mark a direction of a course with a chalk or a felt-tip pen. Change of a direction of a course before a maintained belt can lead to its damage.

Turn off the tension screw and remove полиwedge a belt.
Remove damper крутильных fluctuations.

Installation
Establish in return sequence.

THE NOTE
Replace bolts which were tightened with доворотом.
Гаситель крутильных fluctuations it is established only in one position – pay attention to unloading plugs.

Establish поликлиновый a belt.
Establish a framework of a radiator by means of Ustanovkanyh of details.
Lower an emphasis against проворачивания at the expense of a body weight on the rubber buffer and fasten bolts.
Establish a casing of a forward bumper.
Check up adjustment of headlights.

The inhaling moments
Демпфер крутильных fluctuations to crankshaftу: 22 Нм +45 *.
Emphasis of a support of jet bent for to a radiator framework **: 28 Нм.
* 45 there correspond 1/8 turns.
** Replace bolts.


2.9.2. Removal and installation semi wedge a belt

2.9.4. Epiploon replacement crankshaftа on the party of a belt pulley