Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.8.1. Engine number
2.8.2. Removal and installation semi wedge a belt
2.8.3. Removal and installation damperа крутильных fluctuations
2.8.4. Removal and installation of a forward sealing flange crankshaftа with an epiploon crankshaftа
2.8.5. Removal and installation of a two-mass flywheel (cars from a manual transmission)
2.8.6. Removal and запрессовка the needle bearing of a two-mass flywheel (cars from a manual transmission)
2.8.7. Removal and installation of a conducted disk (cars with АКПП)
2.8.8. Epiploon replacement crankshaftа from outside a chain drive
2.8.9. Removal and installation of the left and right covers приводных chains
2.8.10. Removal and installation of the bottom cover driving chains
2.8.11. A camshaft drive
2.8.12. Removal of a chain drive from cam-shafts, removal and installation натяжителя chains
2.8.13. Removal and installation of a chain of a drive of the oil pump and балансирного a shaft
2.8.14. Removal and installation балансирного a shaft
2.8.15. Removal and installation of a cranked shaft
2.8.16. Shatunno-piston group
2.8.17. Check of a radial backlash of rods
2.8.18. Compression check
2.8.19. Removal and installation of cam-shafts
2.8.20. Replacement маслосъемных caps
2.8.21. Check of basic elements with hydrojacks
2.8.22. Check of directing plugs of valves
2.9. A mechanical part (petrol engines 4,2)
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f


2-8-6-snyatie-i-zapressovka-igolchatogo-podshipnika-dvukhmassovogo-makhovika-avtomobili.html

2.8.6. Removal and запрессовка the needle bearing of a two-mass flywheel (cars from a manual transmission)

Operating procedure
Remove a check point.
Remove press a coupling disk.

Fig. 2.313. Depth measurement запрессовки the needle bearing in a two-mass flywheel


Measure and write down depth запрессовки (size x) the needle bearing in a two-mass flywheel for the further assemblage (fig. 2.313).

Fig. 2.314. Extraction of the needle bearing


Take the needle bearing by means of an internal stripper and a countersupport (fig. 2.314).

THE NOTE
The plastic ring in a two-mass flywheel is susceptible to blows. At damage of a plastic ring – replace a two-mass flywheel.


Fig. 2.315. Запрессовка the needle bearing


Запрессуйте the needle bearing оправкой in a two-mass flywheel (fig. 2.315).
Запрессуйте the needle bearing an underside aligning send before achievement of preliminary measured depth of landing.
Then check up depth запрессовки (size x) the needle bearing in a two-mass flywheel (fig. 2.313).
Establish press a coupling disk.
Establish a check point.


2.8.5. Removal and installation of a two-mass flywheel (cars from a manual transmission)

2.8.7. Removal and installation of a conducted disk (cars with АКПП)