Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.8.1. Engine number
2.8.2. Removal and installation semi wedge a belt
2.8.3. Removal and installation damperа крутильных fluctuations
2.8.4. Removal and installation of a forward sealing flange crankshaftа with an epiploon crankshaftа
2.8.5. Removal and installation of a two-mass flywheel (cars from a manual transmission)
2.8.6. Removal and запрессовка the needle bearing of a two-mass flywheel (cars from a manual transmission)
2.8.7. Removal and installation of a conducted disk (cars with АКПП)
2.8.8. Epiploon replacement crankshaftа from outside a chain drive
2.8.9. Removal and installation of the left and right covers приводных chains
2.8.10. Removal and installation of the bottom cover driving chains
2.8.11. A camshaft drive
2.8.12. Removal of a chain drive from cam-shafts, removal and installation натяжителя chains
2.8.13. Removal and installation of a chain of a drive of the oil pump and балансирного a shaft
2.8.14. Removal and installation балансирного a shaft
2.8.15. Removal and installation of a cranked shaft
2.8.16. Shatunno-piston group
2.8.17. Check of a radial backlash of rods
2.8.18. Compression check
2.8.19. Removal and installation of cam-shafts
2.8.20. Replacement маслосъемных caps
2.8.21. Check of basic elements with hydrojacks
2.8.22. Check of directing plugs of valves
2.9. A mechanical part (petrol engines 4,2)
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







2-8-14-snyatie-i-ustanovka-balansirnogo-vala.html

2.8.14. Removal and installation балансирного a shaft

Fig. 2.364. Components балансирного a shaft: 1 – the sliding bearing; 2 – a bolt 60 Нм; 3 – a counterbalance (from outside a chain drive); 4 – a bolt 9 Нм; 5 – a bearing board; 6 – a counterbalance from outside a belt pulley; 7 – a bolt 60 Нм; 8 – the bearing of sliding 9 – балансирный a shaft



Removal

Fig. 2.44. Bolts of an exhaust pipe of an independent additional heater


On cars with an independent heater unscrew bolts of an exhaust pipe of an independent / additional heater on шумоизоляционном the screen (fig. 2.44).

Fig. 2.45. Fastening of a forward noise isolation


Unblock clamps 1–3 and remove forward and back шумоизоляционные screens (fig. 2.45).
Put the adaptation for откачки oils under the engine.
Merge engine oil.
Remove the engine.
Disconnect the power unit.
Fix the engine at the Adjusting stand.

Cars from a manual transmission
Remove press a disk of coupling and a two-mass flywheel.

Cars with АКПП
Remove a conducted disk of coupling.
Remove a forward sealing flange.
Remove the left and right covers driving chains.
Remove the bottom cover of a chain drive.
Remove a chain of a drive of the oil pump and балансирного a shaft.
In order to avoid reception резаных wounds to wind the end and cutters of a 8-millimetric drill with an insulating tape.

Fig. 2.365. Counterbalance fixing


Fix a back counterbalance 2 on the engine a 8-millimetric drill of poses. 1 (fig. 2.365).
Unscrew a bolt 3 and remove a counterbalance with балансирного a shaft.

Fig. 2.366. Removal of a forward counterbalance


Unscrew a bolt 2, keeping a counterbalance a punch, and remove a forward counterbalance 1 on the engine with балансирного a shaft (fig. 2.366).

Fig. 2.367. Bolts of fastening of a board of the back bearing балансирного a shaft


Unscrew bolts and remove a board of the back bearing балансирного a shaft on the engine (fig. 2.367).
Take балансирный a shaft back from the block of cylinders.

Installation
Коленвал 1 it is fixed by a fixing bolt in ВМТ.
Installation is carried out in return sequence.

THE NOTE
Counterbalance насаживается on балансирный a shaft only in one position.

Establish a chain of a drive of the oil pump and балансирного a shaft.
Establish the bottom cover of a chain drive.
Establish the case of the oil filter.
Establish covers left and right приводных chains.
Establish an epiploon crankshaftа from outside driving chains.
Establish a forward sealing flange.

Cars from a manual transmission
Establish press a disk of coupling and a two-mass flywheel.

Cars from an automatic transmission
Establish a conducted disk of coupling.
Fasten a check point to the engine and establish the power unit.
Fill in engine oil and check up its level.

The inhaling moments
Bearing board to the block of cylinders: 9 Нм.
Counterbalance to балансирному to a shaft: 60 Нм.
Carving stopper in the block цилиндров*: 14 Нм.
* Establish with a new sealing ring.


2.8.13. Removal and installation of a chain of a drive of the oil pump and балансирного a shaft

2.8.15. Removal and installation of a cranked shaft