Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.6.1. Removal and installation turbocharger
2.6.2. Removal and installation of the vacuum block turbocharger
2.6.3. Adjustment of the vacuum block turbocharger (турбонагнетатель it is removed)
2.6.4. The general instructions on self-diagnostics of system of injection
2.6.5. Decrease in a high pressure of fuel
2.6.6. Removal and installation of a flowmeter of air
2.6.7. Removal and installation of an inlet collector from a fuel stage
2.6.8. Removal and installation of a fuel stage (Rail)
2.6.9. Removal and installation of atomizers
2.6.10. Check of pressure of fuel and residual pressure in front of the high pressure pump
2.6.11. Check of residual pressure
2.6.12. Removal and installation of the pump of a high pressure
2.6.13. Replacement of the block of management of the engine
2.6.14. Removal and ljambda-probe installation in front of the catalyst
2.6.15. Removal and installation a ljambda-probe after the catalyst
2.6.16. A fuel tank (front-wheel cars – all models with engines MPI and 2,0 l FSI)
2.6.17. Откачка fuel from a tank
2.6.18. Removal and installation of a fuel tank from hinged details
2.6.19. Electric check of the fuel pump
2.6.20. Check of quantity of fuel submitted the fuel pump (cars with 4 cylinder engine with a free admission)
2.6.21. Check of quantity of fuel submitted the fuel pump (атомобили with the engine of 1,8 l Turbo)
2.6.22. Check of quantity of fuel submitted the fuel pump (атомобили with 4 cylinder engine FSI)
2.6.23. Check of quantity of fuel submitted the fuel pump (cars with 6 cylinder engine MPI)
2.6.24. Removal and installation of knot of giving of fuel
2.6.25. A fuel tank (all-wheel drive cars till 10.04)
2.6.26. Откачка fuel from a tank
2.6.27. Removal and installation of knot of a pedal of an accelerator from gauges of position of a pedal
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.9. A mechanical part (petrol engines 4,2)
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f

2-6-15-snyatie-i-ustanovka-lyambda-zond-posle-katalizatora.html

2.6.15. Removal and installation a ljambda-probe after the catalyst

Removal

Fig. 2.252. Shtekernye connections for a ljambda-probe and heating of a ljambda-probe


Disunite electric штекерное connection 2 (the brown tip) for a ljambda-probe after the catalyst (fig. 2.252).

Fig. 2.253. A site of a ljambda-probe and heating of a ljambda-probe


Unscrew a ljambda-probe after the catalyst 1 by means of the tool from the complete set накидных keys for a ljambda-probe (fig. 2.253).

Installation
Ljambda-probe electroconducting should be necessarily fixed on the former installation sites to avoid contact of electroconducting with an exhaust pipe.
The inhaling moment: 55 Нм.

THE NOTE
New ljambda-probes are greased by adjusting paste; paste hit on grooves of the case of a probe is not supposed.
At use of the ljambda-probe which was in the use it is authorised to grease with heat-resistant paste only a carving. Hit of this paste on grooves of the case of a probe is not supposed.



2.6.14. Removal and ljambda-probe installation in front of the catalyst

2.6.16. A fuel tank (front-wheel cars – all models with engines MPI and 2,0 l FSI)