Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.3.1. Engine removal
2.3.2. Removal and installation semi wedge a belt
2.3.3. Removal and installation of a belt pulley crankshaftа
2.3.4. Removal and installation of a gear belt
2.3.5. Removal and installation of a sealing flange and a flywheel / a conducted disk
2.3.6. Replacement манжетного consolidations crankshaftа on the party of a belt pulley
2.3.7. Removal and installation of a forward sealing flange
2.3.8. Removal and installation of a two-mass flywheel
2.3.9. Removal and installation of a conducted disk
2.3.10. Removal and installation of a cranked shaft
2.3.11. Removal and запрессовка the needle bearing in crankshaft
2.3.12. Removal and asterisk installation
2.3.13. Dismantling and assemblage of pistons and rods
2.3.14. A head of the block of cylinders
2.3.15. Removal and installation of the valve of 1 system of change of phases timing
2.3.16. Removal and installation of a cover of a head of the block of cylinders
2.3.17. Removal of a head of the block of cylinders
2.3.18. Installation of a head of the block of cylinders
2.3.19. Compression check
2.3.20. Repair клапанного the mechanism
2.3.21. Removal and phase shifter installation
2.3.22. Removal and installation of cam-shafts
2.3.23. Replacement маслосъемных caps (at the established head of the block of cylinders)
2.3.24. Check of directing plugs of valves
2.3.25. Replacement манжетного consolidations of a final cam-shaft
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.9. A mechanical part (petrol engines 4,2)
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f


2-3-9-snyatie-i-ustanovka-vedomogo-diska.html

2.3.9. Removal and installation of a conducted disk

Removal
The engine or transmission should be removed.
Mark position of a conducted disk concerning the engine.

Fig. 2.123. Countersupport Installation sites


Support for coupling fix шестигранным screw M8h45 on a fixing disk. Between a countersupport and a conducted disk establish two шестигранных nuts M10. A countersupport Installation site: And for easing, In for an inhaling (fig. 2.123).
Turn off a conducted disk.
Remove, being more low, compensatory washer being more low.

Installation
Establish a disk of fixing with use подкладной washers with grooves 1.

Fig. 2.124. Components of a conducted disk


Insert and tighten with the moment 30 Нм new screws 3 (fig. 2.124).

Fig. 2.125. Size measurement выступания a conducted disk


Size And measure in three places and to calculate average value (fig. 2.125).
Nominal size: 19,5–21,1 mm.

THE NOTE
It is measured through an aperture in a conducted disk to the milled surface of the block of cylinders.

If the preset value is not reached, remove a conducted disk, remove or insert a levelling washer 2.
Repeat measurement procedure for what fasten a conducted disk the moment 30 Нм (fig. 2.124).
If a preset value in norm, tighten bolts the appropriate moment.
The inhaling moment: a conducted disk to crankshaftу* – 60 Нм +90 **
* Replace a bolt.
** 90 there correspond turn quarters.


2.3.8. Removal and installation of a two-mass flywheel

2.3.10. Removal and installation of a cranked shaft