2.3.17. Removal of a head of the block of cylinders

THE NOTE After installation it is necessary to establish again all fixing elements of cables which are removed or cut off at dismantle.

The polluted engine oil replace.

At hermetic use watch characteristics and working life.

Fig. 2.54. An engine casing

Remove an engine casing (fig. 2.54).

Open a cover of a broad tank of system of cooling.

Fig. 2.44. Bolts of an exhaust pipe of an independent additional heater

In cars with an additional heater unscrew bolts of an exhaust pipe of an independent additional heater from шумоизоляционного the screen (fig. 2.44).

Fig. 2.45. Fastening of a forward noise isolation

Loosen the quick disconnect муфты 1 and 2 also remove a forward noise isolation (fig. 2.45).

Merge cooling liquid.

Remove a gear belt.

Fig. 2.146. Easing of a bolt of fastening of an asterisk of a camshaft

Loosen the a bolt of fastening of an asterisk of a camshaft (use a counterkey) (fig. 2.146).

Fig. 2.147. Removal of a belt pulley of a cam-shaft двузахватным a stripper

Remove a belt pulley of a cam-shaft двузахватным a stripper (fig. 2.147).

Fig. 2.148. Fastening of a back cover of a gear belt

Turn off a back cover of a gear belt from ГБЦ (fig. 2.148).

Disconnect a wire of weight 1.

Fig. 2.68. A weight wire, a motor guard and an absorber hose

Disconnect the vacuum tube going to the amplifier of brakes, from a motor board 2 (fig. 2.68).

Disconnect a hose of an absorber 3.

Fig. 2.69. Water hoses and fastening of a broad tank of system of cooling

Disconnect water hoses 1 and 2 and turn off fastening of a broad tank of system of cooling (fig. 2.69).

Disconnect штекерный a socket going to the gauge of a signalling device of low level ОЖ below on a broad tank of system of cooling.

Fig. 2.70. An electric socket of the gauge of pressure of pressurisation and the left hose наддувочного air

Disconnect an electric socket from the gauge of pressure of pressurisation 1 (fig. 2.70).

Disconnect the left hose for наддувочного air 2.

Fig. 2.51. Air lines to интеркулеру and to турбонагнетателю

Disconnect вохдуховод 1 to турбонагнетателю on the right below (fig. 2.51).

Disconnect an air line 2 to интеркулеру from a radiator framework.

Fig. 2.80. An inlet hose of the air filter / turbocharger and electric sockets

Disconnect electric sockets 1 and 2 and release a cable (fig. 2.80).

Fig. 2.149. Fastening of a submitting oil highway turbocharger and its support

Turn off submitting oil highway turbocharger from the engine 1 (fig. 2.149).

Turn off a bolt of 2 support turbocharger.

Disconnect submitting oil highway turbocharger.

Fig. 2.150. Fastening of the return маслопровода

Remove return маслопровод with turbocharger (fig. 2.150).

Fig. 2.151. A support bolt turbocharger

Loosen the a bolt of 1 support turbocharger on 2 turns (fig. 2.151).

Remove an inlet pipe.

Remove the catalyst.

Uncover ГБЦ.

Fig. 2.152. Sequence of easing of bolts of fastening ГБЦ

Loosen the bolts of fastening ГБЦ, maintaining sequence shown on drawing 2.152.

THE NOTE Check up, whether all hoses and wires between the engine, a body and a transmission are separated.

Remove a head of the block of cylinders.