Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
2.1. The general data
2.2. Predvaritlnye checks
2.3. A Mehanichsky part (petrol engines 2,0л)
2.3.1. Engine removal
2.3.2. Removal and installation semi wedge a belt
2.3.3. Removal and installation of a belt pulley crankshaftа
2.3.4. Removal and installation of a gear belt
2.3.5. Removal and installation of a sealing flange and a flywheel / a conducted disk
2.3.6. Replacement манжетного consolidations crankshaftа on the party of a belt pulley
2.3.7. Removal and installation of a forward sealing flange
2.3.8. Removal and installation of a two-mass flywheel
2.3.9. Removal and installation of a conducted disk
2.3.10. Removal and installation of a cranked shaft
2.3.11. Removal and запрессовка the needle bearing in crankshaft
2.3.12. Removal and asterisk installation
2.3.13. Dismantling and assemblage of pistons and rods
2.3.14. A head of the block of cylinders
2.3.15. Removal and installation of the valve of 1 system of change of phases timing
2.3.16. Removal and installation of a cover of a head of the block of cylinders
2.3.17. Removal of a head of the block of cylinders
2.3.18. Installation of a head of the block of cylinders
2.3.19. Compression check
2.3.20. Repair клапанного the mechanism
2.3.21. Removal and phase shifter installation
2.3.22. Removal and installation of cam-shafts
2.3.23. Replacement маслосъемных caps (at the established head of the block of cylinders)
2.3.24. Check of directing plugs of valves
2.3.25. Replacement манжетного consolidations of a final cam-shaft
2.4. Greasing system
2.5. Cooling system
2.6. Injection system
2.7. System of release of the fulfilled gases
2.8. A mechanical part (petrol engines 3,0; 3,2)
2.9. A mechanical part (petrol engines 4,2)
2.10. A mechanical part (diesel engines 2,0)
2.11. Tables
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







2-3-23-zamena-maslosemnykh-kolpachkov-pri-ustanovlennojj-golovke-bloka-cilindrov.html

2.3.23. Replacement маслосъемных caps (at the established head of the block of cylinders)

Remove camshafts.

THE NOTE
To replace маслосъемные caps of final valves of cylinders 3 and 4, in addition it is necessary to remove the valve рециркуляции ОГ.

Take roller levers and put them on a pure surface. Roller levers in places do not change.
Unscrew spark plugs a candle key.

Fig. 2.168. Installation of a directing plate


Fasten directing plate for engines of 2,0 l and 3,0 l FSI screws with рифлением, as is shown in drawing, to ГБЦ (fig. 2.168).
Result the piston of the corresponding cylinder in «the bottom dead point».
Twist the adapter in a nest of a spark plug and to connect compressed air under the pressure of not less than 6 bar.

Fig. 2.169. Branch of crackers with the help send


Separate sitting tight crackers of valves with the help send and a plastic hammer (fig. 2.169).

Fig. 2.170. Installation of the adaptation with a pendant plug


Twist the adaptation with a pendant plug in directing plate for engines of 2,0 l and 3,0 l FSI (fig. 2.170).
Insert an adjusting cartridge into directing plate for engines of 2,0 l and 3,0 l FSI.
Suspend a press plug to the adaptation.

THE NOTE
On the release party the press plug should be suspended, as is shown in drawing 2.170.

Press an adjusting cartridge downwards. Simultaneously twist the screw with накаткой an adjusting cartridge to the right while the ends will not enter into valve crackers.

Fig. 2.171. Grab of an adjusting cartridge


Slightly turn the screw with накаткой forward and back, at the expense of it valve crackers are unclenched also a cartridge is grasped (fig. 2.171).
Release a press plug.
Take an adjusting cartridge.

Fig. 2.172. Removal маслосъемного a cap


Remove маслосъемные caps by means of a stripper (fig. 2.172).

Fig. 2.173. Выпрессовка a pin and nozzle removal


If because of shortage of a place for маслосъемных caps it is not possible to use a stripper, выпрессуйте a pin выколоткой and remove a nozzle (fig. 2.173).
Put the bottom part of a stripper маслосъемных caps to маслосъемному to a cap.
Insert выколотку 1 into an aperture in the bottom part of a stripper.

Fig. 2.174. Extraction маслосъемного a cap


Hook the adjusting adaptation the lever and take, thus, маслосъемный a cap (fig. 2.174).
Installation маслосъемных caps
To avoid damage new маслосъемных caps In, dress on a valve core the plastic plug And (fig. 2.175).

Fig. 2.175. Installation new маслосъемного a cap


Grease a working edge маслосъемного a cap In engine oil, insert into the adaptation for напрессовки and accurately press into directing plug.
Take the plastic plug And.
Insert a spring and a plate of a spring of the valve.
Establish the adaptation for installation, as is shown in drawing 2.170.

Fig. 2.176. The adjusting adaptation



THE NOTE
After extraction of crackers of the valve from an adjusting cartridge at first they are necessary for inserting into the adjusting adaptation (fig. 2.176).

Press an adjusting cartridge from above on the adjusting adaptation and remove valve crackers.
Press an adjusting cartridge by means of a press plug downwards and twist the screw with накаткой adjusting a cartridge forward-back, thus to extend it upwards.
Unload a press plug at the extended screw with накатанной a head.
Remove the adaptation for installation.
The further installation and assemblage is carried out in return to sequence removal.


2.3.22. Removal and installation of cam-shafts

2.3.24. Check of directing plugs of valves