Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
7.1. The general data
7.2. Power supplies system
7.3. The generator
7.4. A starter
7.5. Relay blocks, sockets and safety locks
7.5.1. Removal and installation of the block of management of a combination of devices
7.5.2. Multicontact sockets in the block of management of a combination of devices
7.5.3. Removal and installation of the block of safety locks
7.5.4. Removal and installation of the block of management of an onboard network
7.5.5. Removal and installation of the 9-nested block of the relay
7.5.6. Removal and installation of the 3-nested block of the relay
7.5.7. Removal and installation of the 4-nested block of the relay
7.5.8. Removal and installation left штекерной pads
7.5.9. Removal and installation of the central block of management of system Komfort
7.5.10. Removal and installation right штекерной pads
7.5.11. Removal and installation of a box of the main safety lock in a luggage carrier behind at the left – Audi RS4
7.5.12. Removal and installation of the block of the main safety lock – cars with the accumulator in a motor compartment
7.5.13. The general instructions on repair electricians of the car
7.5.14. Repair of wires of tyre CAN
7.5.15. Breakage of a wire with repair in two places
7.5.16. Repair of contacts in cases of sockets
7.5.17. Mechanical blocking of the case of a socket
7.5.18. Round contacts
7.5.19. Flat contacts to asymmetrical lock uvulas
8. A body
9. Electric equipment schemes
 




9975039f

7-5-18-kruglye-kontakty.html

7.5.18. Round contacts

THE NOTE
Before an unblocking of contacts it is necessary to unblock or remove at presence case clamps (secondary fastenings) the special tool.


Fig. 7.124. Master key input in шлиц in the socket case


Enter approaching for the case of a socket a master key in шлиц in the socket case (fig. 7.124).
Undertake a wire to contact and slightly press it in a socket

THE NOTE
At the expense of cave-in of a tip in the case of a socket from a coat hanger in a socket lock uvulas of a tip act in film, and by means of their master key it is possible to deduce from the socket case freely.

Simultaneously press a master key into the case of a socket and extend the unblocked tip.
The master key after contact extraction can be removed again from шлица in the socket case.

Flat contacts

THE NOTE
Before an unblocking of contacts it is necessary at presence unblock or remove case clamps (secondary fastenings) the special tool.

Flat contacts to one lock uvula
Enter approaching for the case of a socket a master key in шлиц in the socket case.
Undertake a wire to contact and slightly press it in a socket

THE NOTE
At the expense of cave-in of a tip in the case of a socket from a coat hanger in a socket the lock uvula of a tip acts in film, and by means of its master key it is possible to deduce from the socket case freely.


Fig. 7.125. Extraction of the unblocked tip


Simultaneously press a master key into the case of a socket and extend the unblocked tip (fig. 7.125).
Master key after contact extraction it is possible again remove from шлица in the socket case.

Flat contacts to two lock uvulas
Enter approaching for the case of a socket a master key in шлиц in the socket case.
Undertake a wire to contact and against the stop press it in a socket

THE NOTE
At the expense of cave-in of a tip in the case of a socket from a coat hanger in a socket lock uvulas of a tip act in film, and by means of their master key it is possible to deduce from the socket case freely.

Simultaneously press a master key into the case of a socket and extend the unblocked tip
The master key after contact extraction can be removed again from шлица in the socket case.


7.5.17. Mechanical blocking of the case of a socket

7.5.19. Flat contacts to asymmetrical lock uvulas