Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
6.1. Preliminary checks
6.2. Repair of brake system
6.3. Repair of brakes of forward wheels
6.3.1. Removal and installation brake pads
6.3.2. A brake of forward wheels FN3
6.3.3. Removal and installation brake pads
6.3.4. A ceramic brake of forward wheels CSIC
6.3.5. Removal and installation brake pads
6.3.6. Removal and installation brake pads (a brake of back wheels C38)
6.3.7. A brake of back wheels RS4 (TYPE 8EC) / C43
6.3.8. Removal and installation of cables of a lay brake, cars from a forward drive
6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)
6.3.10. Removal and installation of the lever of a manual brake
6.3.11. Removal and installation of a basic pillow for a brake pedal
6.4. System ABS
6.5. Tables
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f

6-3-9-snyatie-i-ustanovka-trosov-stoyanochnogo-tormoza-avtomobili-s-polnym-privodom.html

6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)

THE NOTE
Adjusting elements of cables of a lay brake are in front of back bottom levers.

Removal
Remove the extension piece of the central console.
Remove wheels
Disconnect a back exhaust pipe
Remove теплоизоляционный the screen behind on a tank
Remove a back tunnel filter (passing under a power shaft)
Remove a back tunnel filter (passing over a power shaft)

Fig. 6.47. A lock washer of a cable of a lay brake


Take a lock washer 1 and to unhook cables of a lay brake from a support (fig. 6.47).

THE NOTE
Do not damage the goffered cover of a cable of a lay brake at removal and installation.


Fig. 6.52. Rings for cable positioning


Unblock a cable of a brake 1 of the holder 3 (fig. 6.52).

Fig. 6.53. Держательтроса


Release a cable of a brake 3 of the holder 2 (fig. 6.53).

Fig. 6.54. An unblocking of cables


Unblock cables of a brake 1 of holders 2 and 4 (fig. 6.54).
To have possibility hang new cables, it is necessary remove the lever of a lay brake and establish the mechanism in a starting position.

Installation

Fig. 6.55. Installation of cables


Block a cable 1 against the stop (fig. 6.55).
The tightening loop of the holder should be between both rings for positioning 5

THE NOTE
The place of a clip of the holder 4 should be always turned outside of the car (fig. 6.54).

The moment of an inhaling of poses. 3 makes 1,5 Нм
Hang a cable of a support of an exhaust pipe.
Fix a cable of a lay brake on the bottom or a tank and insert into the lever of a brake support.

THE NOTE
Do not damage the goffered cover of a cable of a lay brake at removal and installation.

Hang a cable of a lay brake on a support and establish a lock washer 1 (fig. 6.47).
Rings 1 for cable positioning should is between points of a clip of the holder (fig. 6.52).
The moment of an inhaling of poses. 2: 25 Нм.
Mount теплоизоляционные screens.
Adjust a manual brake.
Establish the extension piece of the central console.


6.3.8. Removal and installation of cables of a lay brake, cars from a forward drive

6.3.10. Removal and installation of the lever of a manual brake