Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
6.1. Preliminary checks
6.2. Repair of brake system
6.3. Repair of brakes of forward wheels
6.3.1. Removal and installation brake pads
6.3.2. A brake of forward wheels FN3
6.3.3. Removal and installation brake pads
6.3.4. A ceramic brake of forward wheels CSIC
6.3.5. Removal and installation brake pads
6.3.6. Removal and installation brake pads (a brake of back wheels C38)
6.3.7. A brake of back wheels RS4 (TYPE 8EC) / C43
6.3.8. Removal and installation of cables of a lay brake, cars from a forward drive
6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)
6.3.10. Removal and installation of the lever of a manual brake
6.3.11. Removal and installation of a basic pillow for a brake pedal
6.4. System ABS
6.5. Tables
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







6-3-10-snyatie-i-ustanovka-rychaga-ruchnogo-tormoza.html

6.3.10. Removal and installation of the lever of a manual brake

Removal
Remove the extension piece of the central console.

Fig. 6.56. A handle unblocking


The handle 1 unblock a screw-driver 3 and take (fig. 6.56).

Fig. 6.57. Cover and handle removal


Uncover 4 and the handle 1 (fig. 6.57).

Fig. 6.58. An arm of the lever of a lay brake


Unscrew the screw 2 with шестигранной a head and remove an arm 1, the moment of an inhaling 6 Н·м (fig. 6.58).
With two suspended cables
Insert a screw-driver into an unblocking aperture.
Press a screw-driver in a direction «the middle of a range of adjustment».
Keep a screw-driver pressed and slowly put in action the lever of a lay brake.

THE NOTE
Watch that hooks have not jumped out of cable eyes.

Remove a screw-driver.
To lower cables of a lay brake.

With one suspended cable

Fig. 6.59. An unblocking of the mechanism of a lay brake


Unblock the mechanism by means of a screw-driver 2, simultaneously press the second hook of a latch 1 screw-driver in the opposite direction (fig. 6.59).
Turn off nuts with a fillet 1, the moment of an inhaling 25 Н·м.
Disconnect the contact switch of a lay brake

Fig. 6.60. Fastening of the lever of a lay brake


Remove the lever of a lay brake 2 from the console (fig. 6.60).
Establish the adjusting mechanism in a starting position
Clamp a latch hook in a vice.

Fig. 6.61. A mechanism unblocking


Unblock the mechanism by means of a screw-driver 2, simultaneously press the second hook of a latch a screw-driver in the opposite direction (fig. 6.61).

Installation
Installation is carried out in return sequence.
Establish the extension piece of the central console.
Tighten a hand both nuts 1.

THE NOTE
Access to a back nut is available through an aperture for an ashtray, and to a forward nut – through dredging in a floor of a ware compartment.


Fig. 6.62. Lever alignment


Level the lever of a lay brake on the middle of mine of the central console (fig. 6.62).
Tighten nuts, the moment of an inhaling 25 Н·м.
Adjust a manual brake.


6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)

6.3.11. Removal and installation of a basic pillow for a brake pedal