Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
6.1. Preliminary checks
6.2. Repair of brake system
6.3. Repair of brakes of forward wheels
6.3.1. Removal and installation brake pads
6.3.2. A brake of forward wheels FN3
6.3.3. Removal and installation brake pads
6.3.4. A ceramic brake of forward wheels CSIC
6.3.5. Removal and installation brake pads
6.3.6. Removal and installation brake pads (a brake of back wheels C38)
6.3.7. A brake of back wheels RS4 (TYPE 8EC) / C43
6.3.8. Removal and installation of cables of a lay brake, cars from a forward drive
6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)
6.3.10. Removal and installation of the lever of a manual brake
6.3.11. Removal and installation of a basic pillow for a brake pedal
6.4. System ABS
6.5. Tables
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







6-3-8-snyatie-i-ustanovka-trosov-stoyanochnogo-tormoza-avtomobili-s-perednim-privodom.html

6.3.8. Removal and installation of cables of a lay brake, cars from a forward drive

Removal
Remove the extension piece of the central console.
Remove wheels
Remove a floor flooring in a back part at the left and on the right and расклипсовать cables of a lay brake
The floor flooring at the left fastens прибл. 8 screws
Remove a floor flooring inside on system of release ОГ
Disconnect a back exhaust pipe

Fig. 6.47. A lock washer of a cable of a lay brake


Take a lock washer 1 and to unhook cables of a lay brake from a support (fig. 6.47).

THE NOTE
Do not damage the goffered cover of a cable of a lay brake at removal and installation.


Fig. 6.48. Liberation of the brake pipeline


Release the brake pipeline 2 of the holder 3 (fig. 6.48).

Fig. 6.49. Liberation of a cable of a lay brake


Release cables of a lay brake 1 from a fuel tank (клипса) 2 (fig. 6.49).

Fig. 6.50. The holder of a cable of a lay brake


Release cables of a lay brake 3 of the holder 1 (fig. 6.50).
To have possibility hang new cables, it is necessary to remove the lever of a lay brake and to establish the mechanism in a starting position.

Installation

Fig. 6.51. Installation of a cable of a lay brake


Block a cable against the stop (fig. 6.51).

THE NOTE
In a point of a crossing the cable 1 should lie under a cable 2.

Block a cable in provided for this purpose holders.
The tightening loop of the holder should be between both rings for positioning 4 (fig. 6.50).
The moment of an inhaling of poses. 2: 25 Нм
Fix a cable of a lay brake on the bottom or on a tank.

THE NOTE
Do not damage the goffered cover of a cable of a lay brake at removal and installation.

Hang a cable of a lay brake on a brake support and establish a lock washer 1 (fig. 6.47).

Fig. 6.52. Rings for cable positioning


Rings 1 for cable positioning should is in a clip of the holder (fig. 6.52).
The moment of an inhaling of poses. 2: 25 Нм
Mount теплоизоляционные screens.
Establish the extension piece of the central console.
Adjust a manual brake.


6.3.7. A brake of back wheels RS4 (TYPE 8EC) / C43

6.3.9. Removal and installation of cables of a lay brake (cars with a full drive)