Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
3.1. Coupling
3.2. A mechanical transmission
3.3. An automatic transmission
3.3.1. Marks КП
3.3.2. Refuelling volumes
3.3.3. Check of level of oil ATF and its pouring
3.3.4. The general instructions for repair carrying out
3.3.5. Electronic elements АКПП and places of their installation
3.3.6. Check of a drive of inclusion of transfers
3.3.7. Removal and installation of a drive of inclusion of transfers
3.3.8. Removal and installation of the handle of selector AKPP
3.3.9. Adjustment of a cable of selector AKPP
3.3.10. Removal and installation блокиратора
3.3.11. Adjustment блокиратора
3.4. The privodnoj mechanism
3.5. Tables
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 







3-3-7-snyatie-i-ustanovka-privoda-vklyucheniya-peredach.html

3.3.7. Removal and installation of a drive of inclusion of transfers

Removal
Remove selector AKPP handle.

Fig. 3.94. Panel removal


Open an ashtray on the average console and remove the panel (fig. 3.94).
Remove the module of management of the conditioner.
Remove an ashtray of the average console

Fig. 3.95. Removal of the panel of the selector


Unblock in aggregate 4 clips and remove the panel 1 together with directing on a direction upwards (fig. 3.95).
Pull out штекерный I will corrode from outside directing.

Fig. 3.96. A detachment штекерного a socket of an electromagnet of blocking of selector AKPP


Disconnect штекерный a socket of an electromagnet of blocking of selector AKPP (fig. 3.96).
Remove блокиратор.

Fig. 3.1. Noise isolation fastening


Open latches 2 and 3 and remove a back part of a noise isolation (fig. 3.1).

Cars with the 4-cylinder engine
Remove internal left and right overlays of a floor of the car.

Fig. 3.97. Fastening of a back cross-beam of a floor


Remove a back cross-beam of a floor of the car, for this purpose turn on болтовые connections 1–4 (fig. 3.97).

All cars

Fig. 3.98. Fastening of a forward cross-beam of a floor


Remove a forward cross-beam of a floor of the car, for this purpose turn on болтовые connections 1–6 (fig. 3.98).

THE NOTE
In drawing 3.98 the car with the 4-cylinder engine is represented.

THE NOTE
The demountable element of a reception pipe cannot be bent more than on 10 – there is a danger of damage.

Separate system of release ОГ on the fixing plug.

Fig. 3.99. Fastening of the heat-shielding screen


Remove located under a drive of inclusion of transfers the heat-shielding screen (fig. 3.99).
Turn on from a drive of inclusion of transfers the bottom cover.
Remove from the bottom cover a cuff of a cable of selector AKPP and remove it back.

Fig. 3.100. Removal of a stopper of a cable of selector AKPP of a drive of inclusion of transfers


Remove in a direction downwards a stopper of 1 cable of selector AKPP of a drive of inclusion of transfers (fig. 3.100).
Put forward a plastic safety spring 2 a little forward and press on a bolt 3 so, how much it is necessary.
Pull out a cable of the selector of a check point 4 of a drive of inclusion of transfers.

THE NOTE
Do not bend and do not break a cable of the selector of a check point.

Turn away a nut.

THE NOTE
For removal of a drive of inclusion of transfers under the car presence of the assistant is required.


Fig. 3.101. Removal of a drive of inclusion of transfers


Press inside on fixing скобы 1 and 2 and simultaneously press downwards on a drive of inclusion of transfers (fig. 3.101).

Installation
Installation is carried out in return sequence.
Establish selector AKPP cable.
Establish блокиратор.
Adjust блокиратор.
Establish release system so that in it there were no internal pressure.
Check up a drive of inclusion of transfers.

The inhaling moments
Drive of inclusion of transfers to a body: 10 Нм.
The bottom cover to a drive of inclusion of transfers: 10 Нм.
Forward cross-beam to a car floor: 55 Нм.
Back cross-beam to a car floor: 60 Нм.


3.3.6. Check of a drive of inclusion of transfers

3.3.8. Removal and installation of the handle of selector AKPP