Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
4.1. Wheels and tyres
4.2. The general data on a car running gear
4.3. Repair of a suspension bracket of forward wheels
4.3.1. General provisions
4.3.2. Loading of a support of a wheel in own weight of the car
4.3.3. Removal and installation of an amortisation rack
4.3.4. Repair of an amortisation rack
4.3.5. Removal of a screw spring
4.3.6. Installation of a screw spring
4.3.7. Removal and case installation Hubs the bearing
4.3.8. Repair of a rotary fist with the established bearing of a nave
4.3.9. Removal and installation of the top lever
4.3.10. Replacement of forward and back support of the top levers
4.3.11. Removal and stretcher installation
4.3.12. Replacement of support of a stretcher
4.3.13. Removal and installation of persistent wedges резинометаллических support
4.3.14. Removal and stabilizer installation
4.4. A back suspension bracket
4.5. Tables
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f

4-3-12-zamena-opor-podramnika.html

4.3.12. Replacement of support of a stretcher

THE NOTE
On cars stretchers of various executions are established.

Stretcher with резинометаллическими support in points крепеления a body stretcher / (all cars except cabriolets). Replacement резинометаллических support is possible.
Stretcher without резинометаллических support in points крепеления a body stretcher/, and with the welded steel plugs (only cabriolets). Steel plugs are not subject to replacement, at damage the stretcher varies.
For replacement of support of a stretcher it is necessary to remove a stretcher.

Removal сайлентблока

Fig. 4.91. Cutting of a rubber ledge to the external basic plug


Cut or cut off a rubber ledge to the external basic plug (fig. 4.91).

THE NOTE
At damage of a paint and varnish covering of a stretcher приняйте measures on anticorrosive protection of a surface.

Removal back сайлентблока

Fig. 4.92. Removal back сайлентблока


Watch correct position of a stripper to exclude its loss (fig. 4.92).

Fig. 4.93. Removal сайлентблока


All сайлентблоки on a stretcher act in film by means of the same special tool (fig. 4.93).

Preparatory installation works for installation of a support of a stretcher

Fig. 4.94. Installation of a stripper and half rings of loose leaves


Establish a stripper and half rings of loose leaves (fig. 4.94).

Installation сайлентблоков

Fig. 4.95. Position adjustment сайлентблоков


Position сайлентблоков should be regulated by means of a long pipe of rectangular section or a ruler (fig. 4.95).
A = 90 5 .
Stretcher clamp in a vice only with soft inserts.

Installation back сайлентблоков

Fig. 4.96. Installation back сайлентблоков


For запрессовки резинометаллических support to use only oil of type G 294 421 A1 (fig. 4.96).
Support a запрессовывайте until оправка will not settle down заподлицо with the top edge of a stripper.
Take a stripper and loose leaf half rings upwards.

Fig. 4.97. Installation of half rings of loose leaves


Establish half rings of loose leaves between the prorate and a stretcher (fig. 4.97).
Запрессуйте a support against the stop.
At damage of a paint and varnish covering of a stretcher to take measures on anticorrosive protection of a surface.

Installation forward сайлентблока

Fig. 4.98. Installation forward сайлентблока


For запрессовки резинометаллических support use only oil of type G 294 421 A1 (fig. 4.98).
Establish half rings of loose leaves in a tube.
Support a запрессовывайте until оправка will not settle down заподлицо with the top edge of a stripper.

Fig. 4.99. Removal of the loose leaf of the bearing


Raise a stripper and remove bearing loose leaves (fig. 4.99).
The prorate replace оправкой 3351/1 and then to уопра запрессуйте a support.
At damage of a paint and varnish covering of a stretcher take measures on anticorrosive protection of a surface.


4.3.11. Removal and stretcher installation

4.3.13. Removal and installation of persistent wedges резинометаллических support