Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
8.1. Hinged elements of a body
8.2. Doors, locks of doors and the roof hatch
8.3. Osteklenie bodies
8.3.1. Removal and installation of the gauge of a rain
8.3.2. Windscreen removal
8.3.3. Preparation for glass installation
8.3.4. Windscreen installation
8.3.5. Removal of the intact lateral glass
8.3.6. Preparation for glass installation
8.3.7. Installation of lateral glass
8.3.8. Removal of the intact back glass
8.3.9. Removal of the broken back glass
8.3.10. Preparation for glass installation
8.3.11. Installation of back glass
9. Electric equipment schemes
 




9975039f


8-3-5-snyatie-nepovrezhdennogo-bokovogo-stekla.html

8.3.5. Removal of the intact lateral glass

Fig. 8.103. Components of lateral glass: 1 – lateral glass; 2 – a decorative overlay of a roof


Components of lateral glass are shown on fig. 8.103.

Lateral glass with consolidation
Stick a zone at edges of glasses with a sticky tape 6 on a textile basis for protection of varnishing against damages.

Fig. 8.104. Vytjagivanie threads for are sharp


Pierce шилом the glutinous platen from within on lateral glass 1 in a rack direction In (fig. 8.104).
To involve a thread for are sharp 4 inside and fix it on the motionless handle 3.
Other end fix on the mobile handle 5 (fig. 8.104).
The assistant should pierce the glutinous platen, as is shown in drawing 8.104.
Spend a thread for are sharp to a bottom through the glutinous platen 2.

THE NOTE
On corners cut cutting movements that it is easier to overcome glue.

Push a thread for are sharp 4 inside and the motionless handle 3 at rack D behind in the glutinous platen 2 (fig. 8.105).

Fig. 8.105. It is sharp the platen


Spend a thread for are sharp 4 on the glutinous platen by means of the mobile handle.
Push a thread for are sharp 4 inside and the motionless handle 3 at a rack With from above in the glutinous platen 2 (fig. 8.106).

Fig. 8.106. The termination of a cutting of glass


Spend a thread for are sharp 4 on the glutinous platen upward by means of the mobile handle (fig. 8.106).
Take out glass from cut.

Lateral glass with a package of the chromeplated overlays
Remove an overlay of racks C/D.
Paste a sticky tape 3 for protection of varnishing against damages at a rack With and D, no less than on sidewallsе (fig. 8.107).

Fig. 8.107. Sticking up of a decorative lath


Take out a decorative lath 1 of скоб in a direction forward 2 (fig. 8.107).

ATTENTION
Do not suppose a bend of a decorative lath of a roof.

By means of a plastic wedge cautiously deduce a decorative lath of a roof 1 of скоб downwards, beginning from a rack With (fig. 8.108).

Fig. 8.108. Extraction of a decorative lath


Raise a decorative lath of a roof at rack D in precisely the same way from скоб and pull out it downwards.
Lay a string on perimetre of lateral glass according to drawing 8.108.
Fix the ends X and Y on two mobile handles from a set of the special tool.
Easy cutting movements pull a thread in a direction of an arrow And and cut the glutinous platen below at sidewallsы and at a roof frame (fig. 8.109).

Fig. 8.109. It is sharp gluing sidewallsы at a roof frame


Then stretch a string in an arrow direction In downwards through the glutinous platen.
Take out glass from an aperture.


8.3.4. Windscreen installation

8.3.6. Preparation for glass installation