3.2.6. Removal and installation of a drive of a gear change

Remove a knob together with a cover.

Fig. 3.55. Removal of the block of management of a central air

Remove the block of management of a central air (fig. 3.55).

Preliminary having lifted the panel 1 in a direction of arrow A, remove it in a direction of arrow B.

Turn away bolts (arrow C) and remove an ashtray 2 from the central console.

Disconnect штекерный a socket of illumination of an ashtray.

Take out from the central console пенопластовые checks.

Remove шумоизоляционный the screen in a direction upwards.

Fig. 3.56. Fastening шумоизоляционного the screen of the case of the mechanism of a gear change

Turn on шумоизоляционный the screen of the case of the mechanism of a gear change (fig. 3.56).

Fig. 3.57. Fastening of the case of the mechanism of a gear change

Turn away a nut (fig. 3.57).

On cars with an independent heater turn away bolts of an exhaust pipe of an independent / additional heater on шумоизоляционном the screen.

Loosen the bolts or clamps 1 and 2 remove forward шумоизоляционный the screen And (fig. 3.1).

Fig. 3.1. Noise isolation fastening

Loosen the clamps 3 (at presence) also remove back шумоизоляционный the screen of Century

THE NOTE It is forbidden to bend a demountable element in a reception pipe more than on 10 .

Fig. 3.58. Tightening collars of system of release ОГ

Disconnect system of release ОГ from tightening collars or a collar (fig. 3.58).

If necessary disconnect a back part of system of release ОГ from fixing loops and remove it.

THE NOTE The assistant is necessary for a detachment of a back part of system of release ОГ.

Fig. 3.59. Fastening of the heat-shielding screen карданного a shaft

Turn away the heat-shielding screen карданного a shaft (fig. 3.59).

Fig. 3.60. The heat-shielding screen of system of release ОГ

Remove the heat-shielding screen of 1 system of release ОГ, being under a gear change drive (fig. 3.60).

Turn away bolts of flange KpP/kardannyj a shaft.

Combine propeller a shaft 2 with back main transfer. SHRUS move on an axis.

Fig. 3.61. Fastening карданного a shaft

Tie up propeller a shaft to the heat-shielding screen (fig. 3.61).

Fig. 3.62. Emphasis installation

Establish an emphasis of the lift of the power unit with the enclosed wooden prorate under the back cross-section lever (fig. 3.62).

Rest the back cross-section lever the lift of the power unit.

At first turn away bolts 1 and 2, and then 3 and 4.

Fig. 3.63. Lowering of the back cross-section lever by means of the lift of the power unit

Slowly lower the back cross-section lever by means of the lift of the power unit until the distance between the cross-section lever and a body will not make x (fig. 3.63).

Distance x=60 mm.

In the presence of the heat-shielding screen of the left power shaft turn away the screen.

Fig. 3.64. Fastening of the lever of switching of a check point to a switching shaft

Turn away a nut 1 and remove the lever of switching of a check point 2 from a shaft of switching of a check point (fig. 3.64).

Turn away a connecting cable 2 from a cable of inclusion of transfers.

Fig. 3.65. Cables of deenergizing and a choice of transfers

Having turned away a bolt with internal шестигранником, remove a cable of a choice of transfers 1 (fig. 3.65).

Remove a gear change drive in the right party.

Installation is carried out in return sequence.

THE NOTE Necessarily replace linings and self-locking nuts.

Establish the cross-section lever of a suspension bracket.

Establish elements of system of release ОГ and to level without a tension.

Establish back шумоизоляционный the screen (at presence).

Adjust a gear change drive.

Establish the block of management of a central air.

Connecting cable to a check point: 23 Нм.

The lever of switching of a check point to a gear change shaft: 23 Нм.

Cable of a choice of transfers to a check point: 40 Нм.

The heat-shielding screen of a power shaft to a check point: 23 Нм.

The heat-shielding screen карданного a shaft to a check point cover: 25 Нм.

Gear change drive to a body: 10 Нм.

The shumoizoljatsionnyj screen to a gear change drive: 10 Нм.