Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
8.1. Hinged elements of a body
8.2. Doors, locks of doors and the roof hatch
8.2.1. Removal and installation of a framework of glass and стеклоподъемника a forward door
8.2.2. Removal and electric motor installation стеклоподъемника
8.2.3. Adjustment of a forward door
8.2.4. Removal of the handle of a door
8.2.5. Removal of the lock of a door
8.2.6. Repair of the central lock
8.2.7. Removal and installation of a framework of glass and стеклоподъемника a back door
8.2.8. Adjustment of a back door
8.2.9. Removal and installation of a wind-shelter guard of the hatch of a roof
8.2.10. Removal and installation sun-protection шторки
8.2.11. Removal and overlay installation
8.2.12. Cover adjustment podemno-sdvizhnogo the hatch
8.2.13. Replacement of a sealant of the panel of the hatch
8.2.14. Clearing of drainage hoses
8.3. Osteklenie bodies
9. Electric equipment schemes
 







8-2-3-regulirovka-perednejj-dveri.html

8.2.3. Adjustment of a forward door

THE NOTE
For exact adjustment of a door on height, an inclination and displacement use the special tool (fig. 8.59).

THE NOTE
The back door should be adjusted.

The width of a joint can be checked up the special tool 3371.
The size A = 3,5 mm 0,5 mm.
The size B = 4,5 mm 0,5 mm.

Adjustment in a longitudinal direction
Adjustment in a longitudinal direction is carried out by easing of bolts And on a rack And the top and-or bottom hinge of a door and moving of a door 2 (thanks to the increased apertures in the hinge and a rack) (fig. 8.60).

Fig. 8.60. The scheme of adjustment of a forward door in a longitudinal direction


The moment of an inhaling 32 Нм

THE NOTE
In drawing 8.60 the bottom hinge of a door is shown.

Adjustment concerning the car centre

Fig. 8.61. The scheme of adjustment of a forward door in rather centre of the car


Adjustment concerning the car centre is carried out by easing of bolts of the hinge In above and-or below and door movings (grooves in the hinge) (fig. 8.61).
The moment of an inhaling 32 Нм

THE NOTE
On the top and bottom hinges of a door it is established on an adjusting bolt with a fillet.
Therefore, as a rule, at performance of repair adjustment is not required.
If nevertheless adjustment is necessary, with a fillet it is possible to replace adjusting bolts with bolts of the same size, lengths and the durabilities offered in the catalogue of spare parts.

THE NOTE
In a back part of a door adjustment is carried out with the help скобы the lock (in a direction to the car centre).

Adjustment with the help скобы the lock
Loosen the bolts 2.
Labels And or arrows With use for lateral adjustment (fig. 8.62).

Fig. 8.62. The scheme of adjustment with the help скобы the lock


Shift bracket the lock 1 so that the door was established заподлицо with a body contour (fig. 8.62).

THE NOTE
Adjustment is authorised only in a direction to the car centre, instead of on height.
Arrow labels In or arrows D use for adjustment on height.
At correct adjustment bracket the lock should enter into the door lock on the centre.

Tighten screws the moment 25 Нм.


8.2.2. Removal and electric motor installation стеклоподъемника

8.2.4. Removal of the handle of a door