Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
3.1. Coupling
3.2. A mechanical transmission
3.3. An automatic transmission
3.4. The privodnoj mechanism
3.4.1. Power shaft repair on трипоидном hinge AAR 2000
3.4.2. Repair of the external hinge of equal angular speeds
3.4.3. Dismantling and assemblage прочеканенного трипоидного hinge AAR 2600i or 3300i
3.4.4. Dismantling трипоидного hinge AAR 2600i or 3300i
3.4.5. Assemblage трипоидного hinge AAR 2600i or 3300i
3.5. Tables
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f


3-4-5-sborka-tripoidnogo-sharnira-aar-2600i-ili-3300i.html

3.4.5. Assemblage трипоидного hinge AAR 2600i or 3300i

Establish a new protective cover of the hinge on a power shaft.

Fig. 3.131. Напрессовка a lock ring


Напрессуйте a lock ring 1 to the middle of teeths (fig. 3.131).

Fig. 3.132. Installation of the assembly tool


Use 3.132 special tools presented in drawing.
Instead of assembly adaptation T10065/2 it is necessary, depending on power shaft execution, to use T10065/3.
Напрессуйте an asterisk on a power shaft
The facet on an asterisk is turned to a power shaft, it serves for convenience of assemblage.
Before монтажем the hinge or an asterisk трипоидного the hinge teeths And

Fig. 3.111. A facet on hinge "Трипод" asterisk

It is necessary to cover with a thin layer of the greasing used for the hinge (fig. 3.111).
Establish an asterisk трипоидного the hinge on a shaft according to a mark and spread against the stop.

Fig. 3.133. Asterisk installation трипоидного the hinge on a shaft


The presented drawing 3.133 concerns only приводный the shaft having a cone on the end.
Use the special tools presented in drawing.
Special tool T10065/2 cannot be rested against a body качения

Fig. 3.134. Asterisk installation трипоидного the hinge on a shaft


The presented drawing 3.134 concerns only the power shafts having the cylindrical end.
Use the special tools presented in drawing.
Напрессуйте an asterisk трипоидного the hinge on a power shaft
The key ring should be fixed with heard click, the asterisk should adjoin to a key ring without a backlash.

Installation of a lock ring

Fig. 3.135. Installation of a lock ring: 1 – pincers (usual)



Enter from the back party of hinge "Трипод" 70 г greasings for power shafts from the repair complete set.
Slightly смажте a body качения
Watch, that bodies качения did not warp.
By means of a plastic hammer spread a hinge element on an asterisk трипоидного the hinge.

Fig. 3.136. Installation of an element of the hinge on an asterisk трипоидного the hinge


In drawing 3.136 the assembly tool for power shaft AAR 3300i is shown.
The remained greasing tyre out in duster the hinge.
Watch correct position duster on a hinge element.
The protective cover should be established in a flute on perimetre of the case of the hinge

Fig. 3.137. Position of an element of the hinge at installation


Establish a hinge element on the average position. The minute/maks see. Position (fig. 3.137).

THE NOTE
At installation of a holder of the hinge in average position let the air out from a hinge cover, for example, by means of a screw-driver.

Establish a collar.

Fig. 3.138. Adjusting position of a collar



THE NOTE
That it was easier to establish screws with an internal gear wreath in a head at power shaft installation, it is necessary, that the eye 2 collars was between ledges (at cut) a flange of 1 holder of the hinge (fig. 3.138).


Fig. 3.139. Fastening of a small collar


Small collar fix by means of pincers (fig. 3.139).


3.4.4. Dismantling трипоидного hinge AAR 2600i or 3300i

3.5. Tables