Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
3.1. Coupling
3.2. A mechanical transmission
3.3. An automatic transmission
3.4. The privodnoj mechanism
3.4.1. Power shaft repair on трипоидном hinge AAR 2000
3.4.2. Repair of the external hinge of equal angular speeds
3.4.3. Dismantling and assemblage прочеканенного трипоидного hinge AAR 2600i or 3300i
3.4.4. Dismantling трипоидного hinge AAR 2600i or 3300i
3.4.5. Assemblage трипоидного hinge AAR 2600i or 3300i
3.5. Tables
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
8. A body
9. Electric equipment schemes
 




9975039f


3-4-3-razborka-i-sborka-prochekanennogo-tripoidnogo-sharnira-aar-2600i-ili-3300i.html

3.4.3. Dismantling and assemblage прочеканенного трипоидного hinge AAR 2600i or 3300i

Fig. 3.118. Components прочеканенного трипоидного hinge AAR 2600i or 3300i: 1 – a collar; 2 – duster hinge "Трипод"; 3 – a collar; 4 – a lock ring; 5 – тарельчатая a spring; 6 – распорное a ring (plastic); 7 – a lock ring; 8 – the SHRUS external; 9 – a bolt; 10 – a collar; 11 – duster an external SHRUS; 12 – a collar; 13 – a power shaft; 14 – a lock ring; 15 – an asterisk трипоидного the hinge; 16 – a lock ring; 17 – a bolt with an internal polyhedron; 18 – a hinge element


Components прочеканенного трипоидного hinge AAR 2600i or 3300i are shown on fig. 3.118.

Shaft greasing трипоидного the hinge

THE NOTE
At replacement duster anew смажте the hinge.

Collar compression on the internal hinge

Fig. 3.119. Collar compression on the internal hinge


Пыльники hinges from rubber stretch by means of pincers for installation of collars (fig. 3.119).

Nozzle of an external SHRUS
Clamp a power shaft in a vice with soft inserts.
Remove the big collar and turn out back a protective cover of the hinge.

Fig. 3.120. Выбивание an internal ring of the SHRUS


Hammer through copper or brass выколотку beat on an internal ring of the SHRUS (fig. 3.120).

Ventilation duster the hinge
At installation of a protective cover of the hinge in it the lowered pressure can be formed.
At movement it causes fold formation.

Fig. 3.121. Pressure alignment at installation of a protective cover of the hinge


For prevention of it, follows before collar putting on выравнять pressure, having raised a protective cover of the hinge (fig. 3.121).

Fig. 3.122. Position распорного rings and тарельчатой springs (from outside wheels): 1 – a lock ring; 2 – тарельчатая a spring; 3 – распорное a ring (plastic)




THE NOTE
The management concerns only collars from stainless steel.

Collar compression on the external hinge

Fig. 3.123. Collar compression on the external hinge


Pincers V.A.G 1682 establish, as is shown in drawing 3.123. Thus it is necessary to watch that blooming edges of pincers adjoined to the basis of ledge B of a collar.
Press out a collar, having turned the running screw torque a key (without turning pincers).
The inhaling moment: 20 Нм.
Use dynamometer a key with a range of regulation 5–50 Нм (for example dynamometer a key).
Watch that the running screw of pincers moved without jammings. If necessary put a small amount of greasing MOS 2.
At the complicated rotation, for example, owing to carving pollution, at the specified moment of an inhaling the necessary effort of compression of a collar is not reached.


3.4.2. Repair of the external hinge of equal angular speeds

3.4.4. Dismantling трипоидного hinge AAR 2600i or 3300i