Audi A4 with 2001- 2005 of release.
1. Operation and car maintenance service
2. The engine
3. Transmission
4. A running gear
5. The steering mechanism
6. Brake system
7. An onboard electric equipment
7.1. The general data
7.2. Power supplies system
7.3. The generator
7.4. A starter
7.4.1. Removal and starter installation (cars with 4-tsil. The petrol engine of 1,6 l, турбированным the engine of 1,8 l, MPI 2,0 l and FSI 2,0)
7.4.2. Cars from 6-cylinders petrol engine MPI of 2,4 l and MPI 3,0 l
7.4.3. Cars with 6-cylinder petrol engine FSI of 3,2 l
7.4.4. Cars with 8-cylinder engine MPI of 4,2 l – Audi S4
7.5. Relay blocks, sockets and safety locks
8. A body
9. Electric equipment schemes
 







7-4-4-avtomobili-s-8-cilindrovym-dvigatelem-mpi-4-2-l-audi-s4.html

7.4.4. Cars with 8-cylinder engine MPI of 4,2 l – Audi S4

Removal
Disconnect a weight wire in the accumulator at the switched off ignition.
Remove a back cover of a motor compartment.

Fig. 7.67. Fastening грузозахватной скобы


Fix грузозахватную bracket on the right back eyes of the engine (fig. 7.67).

THE NOTE
Position 1 in attention do not accept.


Fig. 7.68. Installation traverses


Establish to a traverse on edges of carving connections of wings (fig. 7.68).
Грузозахватную bracket hang on the running screw traverses.
Slightly raise the engine by means of the running screw traverses.
Remove the right forward wheel.
In cars with an independent heater unscrew screws of an exhaust pipe of an independent heater and an additional heater on шумоизоляционном the screen.

Fig. 7.18. Fastening forward шумоизоляционного the screen


Open quick disconnect clamps 1, unscrew screws 2 and remove шумоизоляционный the screen (fig. 7.18).

Fig. 7.69. Nuts of fastening of a regulator of the stabilizer


Turn off nuts 1–4 regulators of the stabilizer at the left and on the right (fig. 7.69).

Fig. 7.70. Fastening of a plait of conducting on the right on the engine console


Remove the holder of a plait of conducting on the right on the console of the engine (arrow) (fig. 7.70).
Turn off a nut 3.

Fig. 7.71. The right console of the engine


Unscrew screws 1 and 2 and remove the right console of the engine (fig. 7.71).

Fig. 7.72. The holder of a highway of a coolant


Turn off the holder on the right coolant highways (fig. 7.72).
Disconnect a socket 1.
Unscrew screws (arrows).

Fig. 7.73. Fastening of a support of the engine


Remove a support of the engine with its pillow (fig. 7.73).

Cars with a mechanical transmission
Turn off the heat-shielding screen of the right power shaft.
Turn off a wire of weight 5.
Remove electric lines 3 and 4.

Fig. 7.74. Electric lines of a starter


Turn off a nut 1 and the screw 2 (fig. 7.74).
Remove a starter.

Cars with an automatic transmission

Fig. 7.75. The heat-shielding screen of the right power shaft


Remove the heat-shielding screen of 1 right power shaft (fig. 7.75).
Turn off a wire of weight 1.
Remove electric cables 3 and 4 (fig. 7.74).
Unscrew screws 2 and 5 (fig. 7.74).
Remove a starter.

Installation
Establish in return sequence.
Establish the console of the engine and to fasten a stretcher.
Establish the stabilizer.
Connect the accumulator.

The inhaling moments
Component: Нм     
Starter to a transmission: 65 Нм.
Plug B + to a starter: 16 Нм.
Weight wire to a starter: 22 Нм.
Engine support to the block цилиндров*: 42 Нм.
The heat-shielding screen of a power shaft to a transmission: 23 Нм.
* To establish with use of a carving varnish; a carving varnish.


7.4.3. Cars with 6-cylinder petrol engine FSI of 3,2 l

7.5. Relay blocks, sockets and safety locks